Difference between revisions of "Gentoo"

From GnuCash
Jump to: navigation, search
m (Early 2007 problems with guile, slib, g-wrap and gnucash: Dropped because obsolete)
 
(35 intermediate revisions by 8 users not shown)
Line 1: Line 1:
= Options =
+
= via Portage =
  
There are 4 options for running gnucash on Gentoo:
+
Both 2.0 and 1.8 are available in Gentoo.  As of September 2006, 2.0.x is
 +
stable on x86 and amd64.
  
 +
* 2.0.x : official portage stable ebuild
 
* 1.8.x : official portage stable ebuild
 
* 1.8.x : official portage stable ebuild
* 1.9.x : non-portage, overlay-able, ebuild of the development releases.  See [http://bugs.gentoo.org/show_bug.cgi?id=122337 Bug#122337].
 
* svn-ebuild : non-portage, overlay-able, ebuild which pulls from SVN.  See [http://bugs.gentoo.org/show_bug.cgi?id=118862 Bug#118862].
 
* svn, direct : just build and install yourself, independent of portage
 
  
If you're unsure which you want, then you want either the 1.8.x stable version or the 1.9.x development/unstable version, and you probably want the latter.
+
The 2.1.x release series are available via an [http://svn.gnucash.org/repo/gnucash/trunk/packaging/ ebuild in the gnucash sources].
  
= Quickstart =
+
= For GnuCash 2.0.x with OFX direct connect =
  
  $ cd «your portage overlay dir»
+
Here is what you need, and the order is important:
  $ mkdir -p app-office/gnucash
 
  $ cd app-office/gnucash
 
  $ <nowiki>wget http://svn.gnucash.org/repo/gnucash/trunk/packaging/gnucash-1.9.x.ebuild -O gnucash-1.9.2.ebuild</nowiki>
 
  $ ebuild gnucash-1.9.2.ebuild digest
 
  $ emerge =gnucash-1.9.2
 
  
= Notes =
+
# Make sure you libofx-0.8.2 or greater installed.
 +
# Make sure you have aqbanking-2.2.1 or better with "USE=hbci" installed, and it has been rebuilt against libofx-0.8.2.
 +
# Finally emerge gnucash-2.0.1 or better with "USE=ofx hbci"
  
If you're unfamiliar with how to setup an portage overlay, see the Gentoo
+
Make sure you use the emerge option <code>--oneshot</code> when emerging the libraries so they're not added to your world list.
Handbook's section on [http://www.gentoo.org/doc/en/handbook/handbook-x86.xml?part=3&chap=5#doc_chap2 adding unoffical ebuilds].
 
  
The 1.9.x and svn ebuilds use the same ebuild script, which changes its
+
=Problems=
behavior based on the package name ("gnucash" or "gnucash-svn").
 
  
The 1.9.x ebuild DEPENDs on the currently (2006-03-06) keyworded
+
The following are some problems you (i did as of Sept. 9 2006) might run into:
x11-libs/goffice ebuild, which itself depends on a masked gnome-extra/libgsf
 
ebuild.  As the gnucash ebuild it itself keyworded ~x86 (and ~amd64), you'll
 
need to add all 3 to your <tt>/etc/portage/package.keywords</tt> file:
 
  
    =app-office/gnucash-1.9.2 ~x86
+
==Emerging libofx-0.8.2==
    =x11-libs/goffice-0.1.0 ~x86
+
 
     =gnome-extra/libgsf-1.13.3 ~x86
+
This version or better of the package is necessary for OFX direct connect support.  As of current speaking (see above) this package is not available in Portage.  So you will have to use an custom overlay ebuild.  If you're unfamiliar with how to setup an portage overlay, see the Gentoo Handbook's section on [http://www.gentoo.org/doc/en/handbook/handbook-x86.xml?part=3&chap=5#doc_chap2 adding unoffical ebuilds] for full details; a short summary is here:
 +
 
 +
*  Emerge the current available version of libofx, which currently is libofx-0.8.1-r1
 +
  An ebuild for 0.8.2 can be found here: http://bugs.gentoo.org/show_bug.cgi?id=146408
 +
*  Create the following directory
 +
  $ mkdir -p /usr/local/portage/dev-libs/libofx
 +
*  Make portage aware of your overlay directory
 +
  $ echo 'PORTDIR_OVERLAY=/usr/local/portage' >> /etc/make.conf
 +
*  Copy libofx-0.8.1-r1 e-build and patches to new overlay directory
 +
  $ cp -R /usr/portage/dev-libs/libofx/libofx-0.8.1-r1.ebuild /usr/local/portage/dev-libs/libofx/libofx-0.8.2.ebuild
 +
*  Finally copy any patches (you proboably will not need these but just in case)
 +
  $ cp -R /usr/portage/dev-libs/libofx/files/* /usr/local/portage/dev-libs/libofx/files/
 +
*  Make a digest
 +
  $ ebuild /usr/local/portage/dev-libs/libofx/libofx-0.8.2.ebuild digest
 +
 
 +
Now edit the ebuild <code>libofx-0.8.2.ebuild</code>.
 +
 
 +
Look for a line at the top of the file that looks like this (you might not have it):
 +
 
 +
  inherit utils
 +
 
 +
If this line exists, comment it out.  The line tells the e-build to apply patches, and it is highly likely you don't need it (more below).
 +
 
 +
  #inherit utils
 +
 
 +
Now look for the src_unpack routine. Note it could be a little different, note the last three lines before the brace, that means a patch was applied.  The src_unpack routine in my case looked like this.
 +
    src_unpack() {
 +
      unpack ${A}
 +
      # because we redefine docdir in src_install, we need to make sure the
 +
      # dtd's go to the right place, LIBOFX_DTD_DIR
 +
      cd "${S}"/dtd
 +
      sed -i -e 's/$(DESTDIR)$(docdir)/$(DESTDIR)$(LIBOFX_DTD_DIR)/g' \
 +
          Makefile.in
 +
      cd "${S}"
 +
      # bug 116208
 +
      epatch "${FILESDIR}"/${P}-tree.diff
 +
    }
 +
 
 +
It is highly probable that the patch is included in the latest software version so,
 +
comment out the last three lines.
 +
 
 +
    src_unpack() {
 +
      unpack ${A}
 +
      # because we redefine docdir in src_install, we need to make sure the
 +
      # dtd's go to the right place, LIBOFX_DTD_DIR
 +
      cd "${S}"/dtd
 +
      sed -i -e 's/$(DESTDIR)$(docdir)/$(DESTDIR)$(LIBOFX_DTD_DIR)/g' \
 +
          Makefile.in
 +
      #cd "${S}"
 +
      # bug 116208
 +
      #epatch "${FILESDIR}"/${P}-tree.diff
 +
    }
 +
 
 +
Save the e-build file, if you made any changes. NOTE: If you made any changes to the e-build file run the digest command again.
 +
 
 +
    $ ebuild /usr/local/portage/dev-libs/libofx/libofx-0.8.2.ebuild digest
 +
 
 +
Now just emerge libofx and you should be upgraded 0.8.2
 +
 
 +
     $ emerge --oneshot libofx
 +
 
 +
==Emerging aqbanking 2.2.1==
 +
 
 +
The package aqbanking-2.2.1 and its dependencies (gwenhywfwar-2.4.0 AND ktoblzcheck-1.11) are currently marked unstable in portage.
 +
 
 +
: As of Oct 10 2006, aqbanking-2.2.1 is '''not''' marked unstable; check the current state of the world before following these instructions, as the keyword markings below are relatively broad in effect. --- [[User:jsled|jsled]]
 +
 
 +
So to get it add these lines to /etc/portage/package.keywords before you emerge aqbanking.
 +
 
 +
    $ echo 'net-libs/aqbanking ~x86' >> /etc/portage/package.keywords
 +
    $ echo 'sys-libs/gwenhwywfar ~x86' >> /etc/portage/package.keywords
 +
    $ echo 'app-misc/ktoblzcheck ~x86' >> /etc/portage/package.keywords

Latest revision as of 14:38, 24 March 2017

via Portage

Both 2.0 and 1.8 are available in Gentoo. As of September 2006, 2.0.x is stable on x86 and amd64.

  • 2.0.x : official portage stable ebuild
  • 1.8.x : official portage stable ebuild

The 2.1.x release series are available via an ebuild in the gnucash sources.

For GnuCash 2.0.x with OFX direct connect

Here is what you need, and the order is important:

  1. Make sure you libofx-0.8.2 or greater installed.
  2. Make sure you have aqbanking-2.2.1 or better with "USE=hbci" installed, and it has been rebuilt against libofx-0.8.2.
  3. Finally emerge gnucash-2.0.1 or better with "USE=ofx hbci"

Make sure you use the emerge option --oneshot when emerging the libraries so they're not added to your world list.

Problems

The following are some problems you (i did as of Sept. 9 2006) might run into:

Emerging libofx-0.8.2

This version or better of the package is necessary for OFX direct connect support. As of current speaking (see above) this package is not available in Portage. So you will have to use an custom overlay ebuild. If you're unfamiliar with how to setup an portage overlay, see the Gentoo Handbook's section on adding unoffical ebuilds for full details; a short summary is here:

  • Emerge the current available version of libofx, which currently is libofx-0.8.1-r1
  An ebuild for 0.8.2 can be found here: http://bugs.gentoo.org/show_bug.cgi?id=146408
  • Create the following directory
  $ mkdir -p /usr/local/portage/dev-libs/libofx
  • Make portage aware of your overlay directory
  $ echo 'PORTDIR_OVERLAY=/usr/local/portage' >> /etc/make.conf
  • Copy libofx-0.8.1-r1 e-build and patches to new overlay directory
  $ cp -R /usr/portage/dev-libs/libofx/libofx-0.8.1-r1.ebuild /usr/local/portage/dev-libs/libofx/libofx-0.8.2.ebuild
  • Finally copy any patches (you proboably will not need these but just in case)
  $ cp -R /usr/portage/dev-libs/libofx/files/* /usr/local/portage/dev-libs/libofx/files/
  • Make a digest
  $ ebuild /usr/local/portage/dev-libs/libofx/libofx-0.8.2.ebuild digest

Now edit the ebuild libofx-0.8.2.ebuild.

Look for a line at the top of the file that looks like this (you might not have it):

  inherit utils

If this line exists, comment it out. The line tells the e-build to apply patches, and it is highly likely you don't need it (more below).

  #inherit utils

Now look for the src_unpack routine. Note it could be a little different, note the last three lines before the brace, that means a patch was applied. The src_unpack routine in my case looked like this.

   src_unpack() {
     unpack ${A}
     # because we redefine docdir in src_install, we need to make sure the
     # dtd's go to the right place, LIBOFX_DTD_DIR
     cd "${S}"/dtd
     sed -i -e 's/$(DESTDIR)$(docdir)/$(DESTDIR)$(LIBOFX_DTD_DIR)/g' \
          Makefile.in
     cd "${S}"
     # bug 116208
     epatch "${FILESDIR}"/${P}-tree.diff
   }

It is highly probable that the patch is included in the latest software version so, comment out the last three lines.

   src_unpack() {
     unpack ${A}
     # because we redefine docdir in src_install, we need to make sure the
     # dtd's go to the right place, LIBOFX_DTD_DIR
     cd "${S}"/dtd
     sed -i -e 's/$(DESTDIR)$(docdir)/$(DESTDIR)$(LIBOFX_DTD_DIR)/g' \
          Makefile.in
     #cd "${S}"
     # bug 116208
     #epatch "${FILESDIR}"/${P}-tree.diff
   }

Save the e-build file, if you made any changes. NOTE: If you made any changes to the e-build file run the digest command again.

   $ ebuild /usr/local/portage/dev-libs/libofx/libofx-0.8.2.ebuild digest

Now just emerge libofx and you should be upgraded 0.8.2

   $ emerge --oneshot libofx

Emerging aqbanking 2.2.1

The package aqbanking-2.2.1 and its dependencies (gwenhywfwar-2.4.0 AND ktoblzcheck-1.11) are currently marked unstable in portage.

As of Oct 10 2006, aqbanking-2.2.1 is not marked unstable; check the current state of the world before following these instructions, as the keyword markings below are relatively broad in effect. --- jsled

So to get it add these lines to /etc/portage/package.keywords before you emerge aqbanking.

    $ echo 'net-libs/aqbanking ~x86' >> /etc/portage/package.keywords
    $ echo 'sys-libs/gwenhwywfar ~x86' >> /etc/portage/package.keywords
    $ echo 'app-misc/ktoblzcheck ~x86' >> /etc/portage/package.keywords